{"id":9947,"date":"2019-07-03T19:52:30","date_gmt":"2019-07-03T19:52:30","guid":{"rendered":"http:\/\/localhost\/bizhubtroubleshooter\/?post_type=epkb_post_type_1&p=9947"},"modified":"2023-12-21T15:24:30","modified_gmt":"2023-12-21T15:24:30","slug":"c1102-bizhub-554e-454e","status":"publish","type":"epkb_post_type_1","link":"https:\/\/apps.kmbizhubvcare.com\/bizhubtroubleshooter\/?epkb_post_type_1=c1102-bizhub-554e-454e","title":{"rendered":"C1102 (bizhub 554e\/454e)"},"content":{"rendered":"\n

Contents <\/p>\n\n\n\n
\nTrouble type<\/td> Main tray up\/down motors drive malfunction<\/td><\/td><\/td><\/td><\/td><\/tr>
\nTrouble code<\/td>\nC1102<\/td><\/td><\/td><\/td><\/td><\/tr>
\nRank<\/td>\nB<\/td><\/td><\/td><\/td><\/td><\/tr>
\nDetection timing<\/td>\n<When FS-533 is installed><\/td>\n\n\nWhile the exit tray is being lifted, the \nstapler movement motor (M107) is not unblocked after the set period of time has \nelapsed after the tray lift up motor (M109) is turned ON.\n\nWhile the exit tray is being lowered, the \nstapler movement motor (M107) is not blocked after the set period of time has \nelapsed after the tray lift up motor (M109) is turned \nON\n<\/td><\/td><\/td><\/td><\/td><\/tr>
<\/td>
<When FS-534 is installed> <\/td>		While the exit tray is being lifted, the main tray upper position sensor (PS26\/PS27) is not blocked and the main tray upper position detect switch (SW2) is not turned ON, even after the main tray up\/down motor (M11) turns by the set number of times. While the exit tray is being lowered, the main tray full detection sensor (PS29) is not blocked after the set period of time has elapsed after the main tray up\/down motor (M11) is turned ON. <\/td><\/td><\/td><\/td><\/tr>
<\/td>
<When FS-535 is installed> <\/td>		The main tray upper limit sensor (PS44\/PS45) is turned ON even after the set period of time has elapsed while the main tray up\/down motor (M5) is energized. The staple paper exit top surface sensor (PS7) is unblocked even after the set period of time has elapsed while the main tray up\/down motor (M5) is energized.<\/td><\/td><\/td><\/td><\/tr>
\nTrouble isolation<\/td>\n–<\/td><\/td><\/td><\/td><\/td><\/tr>
\nRelevant electrical parts<\/td>\n<When FS-533 is installed><\/td>\n\n\nTray lift up motor (M109)\n\nStapler movement motor \n(M107)\n\nFS control board \n(FSCB)\n\n<\/td><\/td><\/td><\/td><\/td><\/tr>
<\/td>
<When FS-534 is installed> <\/td>		Main tray up\/down motor (M11) Main tray upper position sensor\/R (PS26) Main tray upper position sensor\/F (PS27) Main tray full detection sensor (PS29) Main tray upper position detect switch (SW2) FS control board (FSCB) <\/td><\/td><\/td><\/td><\/tr>
<\/td>
<When FS-535 is installed> <\/td>		Main tray up\/down motor (M5) Main tray upper limit sensor\/in (PS44) Main tray upper limit sensor\/out (PS45) Staple paper exit top surface sensor (PS7) FS control board (FSCB) <\/td><\/td><\/td><\/td><\/tr><\/tbody><\/table>\n\n\n\n

\n \n(2)Procedure\n\n\nWhen FS-533 is installed\n\n\n<\/p>\n\n\n\n
\nStep<\/td>\nAction<\/td>\nControl signal<\/td>\nLocation of electrical \ncomponents<\/td><\/tr><\/thead>
\n1<\/td>\nCheck the connector between M109-FSCB CN108 for \nproper connection and correct as necessary.<\/td>\n–<\/td>\n–<\/td><\/tr>
\n2<\/td>\nCheck the connector of M109 for proper drive \ncoupling and correct as necessary.<\/td>\n–<\/td>\n–<\/td><\/tr>
\n3<\/td>\nCheck the connector between PS107-FSCB CN110 for \nproper connection and correct as necessary.<\/td>\n–<\/td>\n–<\/td><\/tr>
\n4<\/td>\nPS107 I\/O check, sensor check<\/td>\nFSCB CN110<\/td>\nFS-533 7-D to E<\/td><\/tr>
\n5<\/td>\nM109 operation check<\/td>\nFSCB CN108<\/td>\nFS-533 10-E<\/td><\/tr>
\n6<\/td> Replace M109<\/a><\/td>\n–<\/td>\n–<\/td><\/tr>
\n7<\/td>\nFSCB CP109 conduction check<\/td>\n–<\/td>\n–<\/td><\/tr>
\n8<\/td> Replace FSCB<\/a>FSCB
FS-533 (Part# A2YUPPH901(Model No. A2YU-WY1) or A2YUPPXN00 (Model No. A2YU-WY2))
FS-534 (Part# A3EPPPBE01)
FS-535 (Part# A2Y1H10002)<\/td>		\n–<\/td>\n–<\/td><\/tr><\/tbody><\/table>\n\n\n\n