C0206 (bizhub C650i/C550i/C450i)

Please search Knowledge Base articles and Bulletins as they may contain relevant information and updated Part information such as Part numbers.

 When PC-116 or PC-216 is installed

Contents

Trouble type	C0206: Tray 3 feeder up/down abnormality (When PC-116 or PC-216 is installed)
Rank	B
Trouble detection condition	The tray 3 upper limit sensor (PS116) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
Trouble isolation	Tray 3
Relevant electrical parts	-Tray 3 lift-up motor (M113) -Tray 3 upper limit sensor (PS116) -PC control board (PCCB) -CPU board (CPUB) -Base board (BASEB)

Procedure

1. Remove the tray and check to see if a piece of paper is not left inside the machine.
2. Check the connector between M113-PCCB CN6C for proper connection and correct as necessary.
3. Check the connector of M113 for proper drive coupling and correct as necessary.
4. Check the connector between PS116-relay CN24-PCCB CN4 for proper connection and correct as necessary.
5. Check CPUB for proper installation and correct as necessary.
6. PS116 I/O check, sensor check
   • Control signal: PCCB CN4-3 (ON)
   • Location of electrical component: PC-116/PC-216 7-C
7. M113 load check
   • Check code: 23
   • Multi code: 6
   • Control signal: PCCB CN6C-8 to 9
   • Location of electrical component: PC-116/PC-216 2-C
8. Replace M113. (Part# 9J06M10300)
9. Replace PCCB. (PC-116 Part# AAV5H00101 / PC-216 Part# AAV5H00201)
10. Replace CPUB. (C450i Part# AA7RH02P02 / C550i Part# AA7PH02P01 / C650i Part# AA7NH02P03)
11. Replace BASEB. (Part# AA7NH02102)

 When PC-417 is installed

Contents

Trouble type	C0206: Tray 3 feeder up/down abnormality (When PC-417 is installed)
Rank	B
Trouble detection condition	The tray 3 upper limit sensor (PS156) is not turned ON (blocked) even after the set period of time has elapsed after the paper lift-up operation for the drawer began.
Trouble isolation	Tray 3
Relevant electrical parts	-Tray 3 lift-up motor (M143) -Tray 3 upper limit sensor (PS156) -PC control board (PCCB) -CPU board (CPUB) -Base board (BASEB)

Procedure

1. Remove the tray and check to see if a piece of paper is not left inside the machine.
2. Check the connector between M143-PCCB CN6 for proper connection and correct as necessary.
3. Check the connector of M143 for proper drive coupling and correct as necessary.
4. Check the connector between PS156-relay CN25-PCCB CN7 for proper connection and correct as necessary.
5. Check CPUB for proper installation and correct as necessary.
6. PS156 I/O check, sensor check
   • Control signal: PCCB CN7-9 (ON)
   • Location of electrical component: PC-417 4-C
7. M143 load check
   • Check code: 23
   • Multi code: 6
   • Control signal: PCCB CN6-4 to 5
   • Location of electrical component: PC-417 5-K
8. Replace M143. (Part# A2X0M12101)
9. PCCB PS300 conduction check
10. Replace PCCB. (Part# AAV5H01401)
11. Replace CPUB. (C450i Part# AA7RH02P02 / C550i Part# AA7PH02P01 / C650i Part# AA7NH02P03)
12. Replace BASEB. (Part# AA7NH02102)

L.3.7.9 (Link to the Field Service Manual)